DIY massive bookcase

DayneDayne Dayne (57)
Feb 4, 2021
10 hours

This bookcase was inspired by the Ikea bookcase system called Ivar. It was heavily modified (and slightly over-engineered). I will take you through my process and hopefully, you’ll learn something!

And if you’re doing this because you’re just plain bored and love DIY stuff, then check out our list of DIY hobbies to occupy you!

cross cut saw ×1
paint supplies ×1
square ×1
Tape MeasureTape MeasureTape Measure ×1
1″ x 10″ x 8′ – pine ×7
2″ x 2″ x 8′ – pine ×10
1″ x 2″ x 8′ – pine ×8

Howchoo is reader-supported. As an Amazon Associate, we may earn a small affiliate commission at no cost to you when you buy through our links.

This step is crucial. I went with construction grade pine for 2 reasons. It is cheap and it is readily available at big box stores. It is a hassle to make something nice with construction grade wood, but it may be worth it if you’re inexperienced (like me) and/or you’re going to paint the thing anyways.

Spend as much time as you need to find the lumber in decent condition. Look for knots in the wood, damage from storage methods, and bows in the faces or the edges of the boards. The assembly can work some small bows out but you want straight wood.

Building supportsBuilding supports

My supports consist of the 2×2’s joined together using dovetails. Dovetails are unnecessarily complicated for this task but I wanted practice. A dado joint would be perfectly sufficient. Check out our guides on both dovetail and dado joints and choose dado because dovetails are ridiculous for this task.

Cutting notches in the shelvesCutting notches in the shelves

I didn’t get a good picture of my process here, but this is the perfect use for the jigsaw. Take your time to mark out the board according to the schematics, then go slowly with the jigsaw. During this step, I had a scrap 2×2 handy to make sure my notches were the right size before moving on.

Painting and stainingPainting and staining

I made the mistake of pre-staining everything. This was a problem for 2 reasons. The stained wood was a mess and I had to touch up everything that got cut or notched.

I highly recommend doing a dry fit with your pieces, then paint or stain everything in one go. I won’t cover which stains or paints to use here as that is a huge topic and one I’m not an authority on.

AssemblyAssembly

Placing all the uprights in the position I expected them to be, I started by sliding the bottom shelf through all the supports. Once it was close to the right position, I moved the supports in place and flattened the shelf. It took a little negotiation so I used a wood block on top of the shelf and hit that with a hammer to avoid damaging the wood. A rubber mallet would be ideal if you have one.

I found general purpose angle brackets and attached them from the wall using a drywall anchor to an upright support on each end near the top.

DecorationDecoration

I hope to one day own enough books that I love to fill this shelf. In the meantime, it will be partially filled with decorations as well.

The simplest guide to making an armband you’re likely to find!
MichaelMichael Michael (175)
Nov 19, 2020
5 minutes

Who doesn’t have an extra sock or two that’s missing a pair – lost forever to the black hole in the dryer! Grab that extra sock and a pair of scissors, and you have yourself a DIY armband for running!

DIY massive bookcase

DayneDayne Dayne (57)
Feb 4, 2021
10 hours

This bookcase was inspired by the Ikea bookcase system called Ivar. It was heavily modified (and slightly over-engineered). I will take you through my process and hopefully, you’ll learn something!

And if you’re doing this because you’re just plain bored and love DIY stuff, then check out our list of DIY hobbies to occupy you!

cross cut saw ×1
paint supplies ×1
square ×1
Tape MeasureTape MeasureTape Measure ×1
1″ x 10″ x 8′ – pine ×7
2″ x 2″ x 8′ – pine ×10
1″ x 2″ x 8′ – pine ×8

Howchoo is reader-supported. As an Amazon Associate, we may earn a small affiliate commission at no cost to you when you buy through our links.

This step is crucial. I went with construction grade pine for 2 reasons. It is cheap and it is readily available at big box stores. It is a hassle to make something nice with construction grade wood, but it may be worth it if you’re inexperienced (like me) and/or you’re going to paint the thing anyways.

Spend as much time as you need to find the lumber in decent condition. Look for knots in the wood, damage from storage methods, and bows in the faces or the edges of the boards. The assembly can work some small bows out but you want straight wood.

Building supportsBuilding supports

My supports consist of the 2×2’s joined together using dovetails. Dovetails are unnecessarily complicated for this task but I wanted practice. A dado joint would be perfectly sufficient. Check out our guides on both dovetail and dado joints and choose dado because dovetails are ridiculous for this task.

Cutting notches in the shelvesCutting notches in the shelves

I didn’t get a good picture of my process here, but this is the perfect use for the jigsaw. Take your time to mark out the board according to the schematics, then go slowly with the jigsaw. During this step, I had a scrap 2×2 handy to make sure my notches were the right size before moving on.

Painting and stainingPainting and staining

I made the mistake of pre-staining everything. This was a problem for 2 reasons. The stained wood was a mess and I had to touch up everything that got cut or notched.

I highly recommend doing a dry fit with your pieces, then paint or stain everything in one go. I won’t cover which stains or paints to use here as that is a huge topic and one I’m not an authority on.

AssemblyAssembly

Placing all the uprights in the position I expected them to be, I started by sliding the bottom shelf through all the supports. Once it was close to the right position, I moved the supports in place and flattened the shelf. It took a little negotiation so I used a wood block on top of the shelf and hit that with a hammer to avoid damaging the wood. A rubber mallet would be ideal if you have one.

I found general purpose angle brackets and attached them from the wall using a drywall anchor to an upright support on each end near the top.

DecorationDecoration

I hope to one day own enough books that I love to fill this shelf. In the meantime, it will be partially filled with decorations as well.

The simplest guide to making an armband you’re likely to find!
MichaelMichael Michael (175)
Nov 19, 2020
5 minutes

Who doesn’t have an extra sock or two that’s missing a pair – lost forever to the black hole in the dryer! Grab that extra sock and a pair of scissors, and you have yourself a DIY armband for running!

 
33
8

DIY massive bookcase

DayneDayne Dayne (57)
Feb 4, 2021
10 hours

This bookcase was inspired by the Ikea bookcase system called Ivar. It was heavily modified (and slightly over-engineered). I will take you through my process and hopefully, you’ll learn something!

And if you’re doing this because you’re just plain bored and love DIY stuff, then check out our list of DIY hobbies to occupy you!

cross cut saw ×1
paint supplies ×1
square ×1
Tape MeasureTape MeasureTape Measure ×1
1″ x 10″ x 8′ – pine ×7
2″ x 2″ x 8′ – pine ×10
1″ x 2″ x 8′ – pine ×8

Howchoo is reader-supported. As an Amazon Associate, we may earn a small affiliate commission at no cost to you when you buy through our links.

This step is crucial. I went with construction grade pine for 2 reasons. It is cheap and it is readily available at big box stores. It is a hassle to make something nice with construction grade wood, but it may be worth it if you’re inexperienced (like me) and/or you’re going to paint the thing anyways.

Spend as much time as you need to find the lumber in decent condition. Look for knots in the wood, damage from storage methods, and bows in the faces or the edges of the boards. The assembly can work some small bows out but you want straight wood.

Building supportsBuilding supports

My supports consist of the 2×2’s joined together using dovetails. Dovetails are unnecessarily complicated for this task but I wanted practice. A dado joint would be perfectly sufficient. Check out our guides on both dovetail and dado joints and choose dado because dovetails are ridiculous for this task.

Cutting notches in the shelvesCutting notches in the shelves

I didn’t get a good picture of my process here, but this is the perfect use for the jigsaw. Take your time to mark out the board according to the schematics, then go slowly with the jigsaw. During this step, I had a scrap 2×2 handy to make sure my notches were the right size before moving on.

Painting and stainingPainting and staining

I made the mistake of pre-staining everything. This was a problem for 2 reasons. The stained wood was a mess and I had to touch up everything that got cut or notched.

I highly recommend doing a dry fit with your pieces, then paint or stain everything in one go. I won’t cover which stains or paints to use here as that is a huge topic and one I’m not an authority on.

AssemblyAssembly

Placing all the uprights in the position I expected them to be, I started by sliding the bottom shelf through all the supports. Once it was close to the right position, I moved the supports in place and flattened the shelf. It took a little negotiation so I used a wood block on top of the shelf and hit that with a hammer to avoid damaging the wood. A rubber mallet would be ideal if you have one.

I found general purpose angle brackets and attached them from the wall using a drywall anchor to an upright support on each end near the top.

DecorationDecoration

I hope to one day own enough books that I love to fill this shelf. In the meantime, it will be partially filled with decorations as well.

The simplest guide to making an armband you’re likely to find!
MichaelMichael Michael (175)
Nov 19, 2020
5 minutes

Who doesn’t have an extra sock or two that’s missing a pair – lost forever to the black hole in the dryer! Grab that extra sock and a pair of scissors, and you have yourself a DIY armband for running!

DIY massive bookcase

DayneDayne Dayne (57)
Feb 4, 2021
10 hours

This bookcase was inspired by the Ikea bookcase system called Ivar. It was heavily modified (and slightly over-engineered). I will take you through my process and hopefully, you’ll learn something!

And if you’re doing this because you’re just plain bored and love DIY stuff, then check out our list of DIY hobbies to occupy you!

cross cut saw ×1
paint supplies ×1
square ×1
Tape MeasureTape MeasureTape Measure ×1
1″ x 10″ x 8′ – pine ×7
2″ x 2″ x 8′ – pine ×10
1″ x 2″ x 8′ – pine ×8

Howchoo is reader-supported. As an Amazon Associate, we may earn a small affiliate commission at no cost to you when you buy through our links.

DIY massive bookcase

DIY massive bookcase
DayneDayne Dayne (57)
Feb 4, 2021
10 hours
Dayne
 
33
8
30 DIY or Low-Cost Hobbies You Can Start at Home Today30 DIY or Low-Cost Hobbies You Can Start at Home Today 30 DIY or Low-Cost Hobbies You Can Start at Home TodayTry a few of these affordable DIY’s and hobbies to stay connected and productive!
30 DIY or Low-Cost Hobbies You Can Start at Home Today
cross cut saw ×1
paint supplies ×1
square ×1
Tape MeasureTape MeasureTape Measure ×1
1″ x 10″ x 8′ – pine ×7
2″ x 2″ x 8′ – pine ×10
1″ x 2″ x 8′ – pine ×8

Howchoo is reader-supported. As an Amazon Associate, we may earn a small affiliate commission at no cost to you when you buy through our links.

cross cut saw ×1
paint supplies ×1
square ×1
Tape MeasureTape MeasureTape Measure ×1
1″ x 10″ x 8′ – pine ×7
2″ x 2″ x 8′ – pine ×10
1″ x 2″ x 8′ – pine ×8
Tape Measure
Table of Contents

Jump to step:

  1. Wood selection
  2. Building supports
  3. Cutting notches in the shelves
  4. Painting and staining
  5. Assembly
  6. Attach to wall using angle brackets
  7. Decoration
 
33
8
In these interests
h/woodworking • 18 guides
h/diy • 97 guides
h/home • 33 guides
h/woodworking • 18 guides
h/diy • 97 guides
h/home • 33 guides

This step is crucial. I went with construction grade pine for 2 reasons. It is cheap and it is readily available at big box stores. It is a hassle to make something nice with construction grade wood, but it may be worth it if you’re inexperienced (like me) and/or you’re going to paint the thing anyways.

Spend as much time as you need to find the lumber in decent condition. Look for knots in the wood, damage from storage methods, and bows in the faces or the edges of the boards. The assembly can work some small bows out but you want straight wood.

This step is crucial. I went with construction grade pine for 2 reasons. It is cheap and it is readily available at big box stores. It is a hassle to make something nice with construction grade wood, but it may be worth it if you’re inexperienced (like me) and/or you’re going to paint the thing anyways.

Spend as much time as you need to find the lumber in decent condition. Look for knots in the wood, damage from storage methods, and bows in the faces or the edges of the boards. The assembly can work some small bows out but you want straight wood.

Wood selection

Building supportsBuilding supports

My supports consist of the 2×2’s joined together using dovetails. Dovetails are unnecessarily complicated for this task but I wanted practice. A dado joint would be perfectly sufficient. Check out our guides on both dovetail and dado joints and choose dado because dovetails are ridiculous for this task.

Building supportsBuilding supports

My supports consist of the 2×2’s joined together using dovetails. Dovetails are unnecessarily complicated for this task but I wanted practice. A dado joint would be perfectly sufficient. Check out our guides on both dovetail and dado joints and choose dado because dovetails are ridiculous for this task.

Building supports

Building supportsHow to make the dado (housing) joint by handHow to Make the Perfect Dovetail Joint Using Traditional Woodworking Tools
Cutting notches in the shelvesCutting notches in the shelves

I didn’t get a good picture of my process here, but this is the perfect use for the jigsaw. Take your time to mark out the board according to the schematics, then go slowly with the jigsaw. During this step, I had a scrap 2×2 handy to make sure my notches were the right size before moving on.

Cutting notches in the shelvesCutting notches in the shelves

I didn’t get a good picture of my process here, but this is the perfect use for the jigsaw. Take your time to mark out the board according to the schematics, then go slowly with the jigsaw. During this step, I had a scrap 2×2 handy to make sure my notches were the right size before moving on.

Cutting notches in the shelves

Cutting notches in the shelves
Painting and stainingPainting and staining

I made the mistake of pre-staining everything. This was a problem for 2 reasons. The stained wood was a mess and I had to touch up everything that got cut or notched.

I highly recommend doing a dry fit with your pieces, then paint or stain everything in one go. I won’t cover which stains or paints to use here as that is a huge topic and one I’m not an authority on.

Painting and stainingPainting and staining

I made the mistake of pre-staining everything. This was a problem for 2 reasons. The stained wood was a mess and I had to touch up everything that got cut or notched.

I highly recommend doing a dry fit with your pieces, then paint or stain everything in one go. I won’t cover which stains or paints to use here as that is a huge topic and one I’m not an authority on.

Painting and staining

Painting and staining
AssemblyAssembly

Placing all the uprights in the position I expected them to be, I started by sliding the bottom shelf through all the supports. Once it was close to the right position, I moved the supports in place and flattened the shelf. It took a little negotiation so I used a wood block on top of the shelf and hit that with a hammer to avoid damaging the wood. A rubber mallet would be ideal if you have one.

AssemblyAssembly

Placing all the uprights in the position I expected them to be, I started by sliding the bottom shelf through all the supports. Once it was close to the right position, I moved the supports in place and flattened the shelf. It took a little negotiation so I used a wood block on top of the shelf and hit that with a hammer to avoid damaging the wood. A rubber mallet would be ideal if you have one.

Assembly

Assembly

I found general purpose angle brackets and attached them from the wall using a drywall anchor to an upright support on each end near the top.

I found general purpose angle brackets and attached them from the wall using a drywall anchor to an upright support on each end near the top.

Attach to wall using angle brackets

DecorationDecoration

I hope to one day own enough books that I love to fill this shelf. In the meantime, it will be partially filled with decorations as well.

DecorationDecoration

I hope to one day own enough books that I love to fill this shelf. In the meantime, it will be partially filled with decorations as well.

Decoration

Decoration
The simplest guide to making an armband you’re likely to find!
MichaelMichael Michael (175)
Nov 19, 2020
5 minutes

Who doesn’t have an extra sock or two that’s missing a pair – lost forever to the black hole in the dryer! Grab that extra sock and a pair of scissors, and you have yourself a DIY armband for running!

The simplest guide to making an armband you’re likely to find!
MichaelMichael Michael (175)
Nov 19, 2020
5 minutes

Who doesn’t have an extra sock or two that’s missing a pair – lost forever to the black hole in the dryer! Grab that extra sock and a pair of scissors, and you have yourself a DIY armband for running!

NEXT UP
DIY Phone Armband for Running
DIY Phone Armband for Running
The simplest guide to making an armband you’re likely to find!
MichaelMichael Michael (175)
Nov 19, 2020
5 minutes
Michael Continue reading
Share this guide!
RedditEmailTextPinterest
Dayne's profile pictureDayne's profile pictureDayne
Joined in 2015 57 guides
Software engineer, co-founder of Howchoo, and renaissance man. Lifelong amateur woodworker, espresso mechanic, freestyle lyricist, drummer, artist, runner, coffee roaster, electrical engineer, gamer, inventor, churner, psychoanalyst, photographer, pizza chef, pit master, audiophile, guitarist, entrepreneur, dad, yogi, cyclist, and barista.
Dayne's profile picture
Related to this guide:
DIY Phone Armband for RunningDIY Phone Armband for Running
The simplest guide to making an armband you’re likely to find!
In these interests: diyfitnessrunning
No Sew Running BeltNo Sew Running Belt
No basketball jerseys were hurt in the making of this guide! Okay, maybe one was.
In these interests: fitnessdiyrunning
DIY Phone Armband for RunningDIY Phone Armband for Running
The simplest guide to making an armband you’re likely to find!
In these interests: diyfitnessrunning
Michael's profile pictureView guide
In these interests: diyfitnessrunning
diyfitnessrunning
No Sew Running BeltNo Sew Running Belt
No basketball jerseys were hurt in the making of this guide! Okay, maybe one was.
In these interests: fitnessdiyrunning
Michael's profile pictureView guide
In these interests: fitnessdiyrunning
fitnessdiyrunningZach's profile pictureView guide
In these interests: retrogamingpiretropie
retrogamingpiretropie
People also read:
Splicer Bunny 3D printed maskSplicer Bunny 3D printed mask
Ditch those latex masks for something much cooler this year!
Raspberry Pi Coffee GrinderRaspberry Pi Coffee Grinder
Put the calculator away, we’re having Pi for coffee.
Anycubic Kobra Go 3D Printer Hands-On ReviewAnycubic Kobra Go 3D Printer Hands-On Review
A detailed review on the Anycubic Kobra Go DIY 3D printer
Raspberry Pi cameraRaspberry Pi camera
Raspberry Pi cameraHow to Take a Photo with Your Raspberry Pi Camera
Splicer Bunny 3D printed maskSplicer Bunny 3D printed mask
Splicer Bunny 3D printed mask10 Awesome 3D Printed Halloween Masks (2022)
Raspberry Pi Coffee GrinderRaspberry Pi Coffee Grinder
Raspberry Pi Coffee GrinderAutomated Coffee Grinder Uses Raspberry Pi To Create Perfect Cup
Anycubic Kobra Go 3D Printer Hands-On ReviewAnycubic Kobra Go 3D Printer Hands-On Review
Anycubic Kobra Go 3D Printer Hands-On ReviewAnycubic’s Kobra Go 3D Printer Hands-On Review
PiCar-V V2.0 KitPiCar-V V2.0 Kit
PiCar-V V2.0 KitDIY Raspberry Pi RC Car: SunFounder’s PiCar-V V2.0 Kit
DIY Dog Door for French Door Window Panes
Setting up a Raspberry Pi ChromecastSetting up a Raspberry Pi Chromecast
Setting up a Raspberry Pi ChromecastHow to Set Up a Raspberry Pi Chromecast
Raspberry Pi Amazon EchoRaspberry Pi Amazon Echo
Raspberry Pi Amazon EchoBuild Your Own Raspberry Pi Amazon Echo
Dog staring at Kong ToyDog staring at Kong Toy
Dog staring at Kong ToyDIY Frozen Kong Toy with At-Home Filling
Cat in mid scratch.Cat in mid scratch.
Cat in mid scratch.DIY Cardboard Cat Scratcher You Can Make Right Now
Posted in these interests:
woodworkingwoodworking
Explore
h/woodworking • 18 guides
“He who works with his hands is a laborer. He who works with his hands and his head is a craftsman. He who works with his hands and his head and his heart is an artist.” – Francis of Assisi
diydiy
Explore
h/diy • 97 guides
“It takes half your life before you discover life is a do-it-yourself project.” – Napoleon Hill
homehome
Explore
h/home • 33 guides
Home is where the heart is.
woodworkingwoodworking
Explore
h/woodworking • 18 guides
“He who works with his hands is a laborer. He who works with his hands and his head is a craftsman. He who works with his hands and his head and his heart is an artist.” – Francis of Assisi
Explore
diydiy
Explore
h/diy • 97 guides
“It takes half your life before you discover life is a do-it-yourself project.” – Napoleon Hill
Explore
homehome
Explore
h/home • 33 guides
Home is where the heart is.
Explore
Discuss this guide!
Discover interesting things!
Explore Howchoo’s most popular interests.
Explore

Follow @howchoo and learn cool things:

Are you a passionate writer? We’re hiring!

Write for Howchoo

Like what we do?

Donate

Want to support Howchoo? When you buy a tool or material through one of our Amazon links, we earn a small commission as an Amazon Associate.

Write for HowchooDonate

Leave a Reply

Your email address will not be published. Required fields are marked *